Canada Gazette, Part I, Volume 153, Number 39: GOVERNMENT NOTICES
September 28, 2019
DEPARTMENT OF HEALTH
HAZARDOUS MATERIALS INFORMATION REVIEW ACT
Decisions, undertakings and orders on claims for exemption
Pursuant to paragraph 18(1)(a) of the Hazardous Materials Information Review Act, the Chief Screening Officer hereby gives notice of the decisions of the screening officer respecting each claim for exemption and the relevant safety data sheet (SDS) and (where applicable) the label listed below.
In accordance with section 20 of the Hazardous Materials Information Review Act, a claimant or any affected party, as defined, may appeal a decision or order of a screening officer. An affected party may also appeal an undertaking in respect of which a notice has been published in the Canada Gazette. To initiate the appeal process, a Statement of Appeal (Form 1) as prescribed by the Hazardous Materials Information Review Act Appeal Board Procedures Regulations must be completed and delivered, along with the fee prescribed by section 12 of the Hazardous Materials Information Review Regulations, within 45 days of the publication of this notice in the Canada Gazette, Part I, to the Chief Appeals Officer at the following address: Workplace Hazardous Materials Bureau, 269 Laurier Avenue West, 8th Floor, 4908B, Ottawa, Ontario K1A 0K9.
Véronique Lalonde
Chief Screening Officer
On February 11, 2015, the Hazardous Products Act (HPA) was amended, and the Controlled Products Regulations (CPR) and the Ingredient Disclosure List were repealed and replaced with the new Hazardous Products Regulations (HPR). The revised legislation (HPA/HPR) is referred to as WHMIS 2015.
All claims for exemption in this publication were filed and evaluated in accordance with the provisions of WHMIS 2015.
A Notice of Filing was published in Part I of the Canada Gazette and there were no written representations from affected parties with respect to any of the claims for exemption and related SDSs or labels mentioned below.
Each of the claims for exemption listed in the table below was found to be valid except for that for Registry Number (RN) 9471, which was found to be partially valid. The screening officer reached this decision after reviewing the information in support of the claim, having regard exclusively to the criteria found in section 3 of the Hazardous Materials Information Review Regulations.
RN | Claimant | Product Identifier | Date of Decision |
---|---|---|---|
9471 | Exaltexx Inc. | Exalt-AMA-100 | 2019-02-15 |
9600 | BYK USA Inc. | BYK-W 966 | 2019-05-03 |
9710 | Multi-Chem Production Chemicals Co. | MC MX 1-1190 | 2019-06-13 |
9727 | Multi-Chem Production Chemicals Co. | MC MX 924-5 | 2019-06-13 |
9824 | Nalco Canada ULC | Torq Free™ HD | 2019-05-30 |
9845 | Nalco Canada ULC | 3D TRASAR 3DT408 | 2019-06-04 |
9962 | BYK USA Inc. | ANTI-TERRA-U 100 | 2019-05-03 |
10033 | Innospec Fuel Specialties LLC | OGI-6140 | 2019-06-05 |
10035 | Innospec Fuel Specialties LLC | OGI-4710 | 2019-07-26 |
10858 | Nalco Canada ULC | AIM1010 | 2019-06-11 |
11130 | Canadian Energy Services | Stimwrx-Poly-CI-A | 2019-06-10 |
11266 | BYK USA Inc. | ANTI-TERRA U | 2019-05-03 |
11267 | BYK USA Inc. | BYK-W 920 | 2019-05-03 |
11795 | Suez Water Technologies& Solutions Canada | PETROFLO 20Y3108 | 2019-07-08 |
12100 | Halliburton Group Canada | HpH Breaker | 2019-06-21 |
12148 | Nalco Canada ULC | 3D TRASAR™ 3DT337 | 2019-07-18 |
The claimant name on which the screening officer issued a decision for the following claim is different from the claimant name that was published in the Notice of Filing.
RN | Notice of Filing Publication Date | Original Claimant Name | New Claimant Name |
---|---|---|---|
11795 | 2017-11-11 | GE Water & Process Technologies Canada | Suez Water Technologies & Solutions Canada |
The subject of the claim on which the screening officer issued a decision for the following claims is different from the subject of the claim that was published in the Notice of Filing.
RN | Notice of Filing Publication Date | Original Subject of the Claim | Revised Subject of the Claim |
---|---|---|---|
9845 | 2016-03-26 | C.i. and C. of one ingredient C. of one ingredient |
C.i. of one ingredient |
10858 | 2017-01-28 | C.i. and C. of three ingredients C. of two ingredients |
C.i. of three ingredients |
Note: C.i. = chemical identity and c. = concentration
In all cases where the SDS or the label was determined not to be in compliance with the relevant legislation, pursuant to subsection 16.1(1) of the Hazardous Materials Information Review Act, the claimant was given 30 days to provide the screening officer with a signed undertaking accompanied by the SDS or the label amended as necessary.
Non-compliances that fall outside the scope of what is required to be published in the Canada Gazette are referred to as “administrative non-compliances.”
Please refer to Health Canada’s List of Active Claims for Exemption for a description of “administrative non-compliances” and their associated corrective measures.
CLAIMS FOR WHICH THE SCREENING OFFICER WAS SATISFIED THAT THE CLAIMANT HAD TAKEN THE MEASURES SET OUT IN THE UNDERTAKING
Pursuant to paragraph 18(1)(b) of the Hazardous Materials Information Review Act, the Chief Screening Officer hereby gives notice of information that has been disclosed on the relevant SDS or label in compliance with an undertaking and the date on which the notice referred to in subsection 16.1(3) of the Act was issued.
RN: 9600
Date of compliance undertaking: 2019-07-12
The claimant had been advised to correct administrative non-compliances in the SDS (or label) and had been further advised to amend the SDS (or label) as indicated below.
- 1. Disclose the Canadian initial supplier identifier.
- 2. Disclose the appropriate restrictions on use.
- 3. Disclose the appropriate first aid measures.
- 4. Correct the disclosure of misleading information regarding the most important symptoms and effects, whether acute or delayed.
- 5. Disclose the product’s boiling range.
- 6. Disclose that the ingredient “naphtha (petroleum), heavy alkylate” has been shown to be an aspiration hazard.
- 7. Correct the disclosure of misleading information regarding skin corrosion/skin irritation.
- 8. Correct the disclosure of misleading information regarding serious eye damage/eye irritation.
RN: 9824
Date of compliance undertaking: 2019-07-11
The claimant had been advised to correct administrative non-compliances in the SDS (or label) and had been further advised to amend the SDS (or label) as indicated below.
- 1. Disclose the information elements concerning the additional hazard and precautionary statements.
- 2. Remove CANUTEC’s emergency telephone number.
- 3. Disclose the additional hazard classification of “Eye Irritation — Category 2” and remove the health hazard classification of “Eye Irritation — Category 2B”.
- 4. Disclose the applicable common names and synonyms for the ingredients “isopropanol” and “diesel fuel No. 2”.
- 5. Disclose, in Section 3, which ingredients are part of a complex mixture and to which complex mixture they belong.
- 6. Disclose the product’s melting point and freezing point.
- 7. Disclose the product’s reactivity.
- 8. Disclose a sufficient description of the delayed and immediate effects, and chronic effects from short-term and long-term exposure.
- 9. Correct the precautionary statements to select the appropriate phrases when a slash is present.
RN: 9845
Date of compliance undertaking: 2019-07-11
The claimant had been advised to correct administrative non-compliances in the SDS (or label) and had been further advised to amend the SDS (or label) as indicated below.
- 1. Remove CANUTEC’s emergency telephone number.
- 2. Disclose the information elements concerning the additional hazard and precautionary statements.
- 3. Disclose the applicable common names and synonyms for the ingredient “benzotriazol”.
- 4. Disclose the applicable information for “the most important symptoms and effects, whether acute or delayed” under Section 4, “First aid measures”.
- 5. Disclose statements conveying the relevant precautionary information in Section 4 of the SDS.
- 6. Disclose statements conveying the relevant precautionary information in Section 7 of the SDS.
- 7. Disclose an adequate product odour.
- 8. Disclose the product’s reactivity.
- 9. Disclose a sufficient description of the delayed and immediate effects, and chronic effects from short-term and long-term exposure.
- 10. Disclose the calculated product inhalation ATE value of 97.8 mg/L (22.4% unknown).
- 11. Disclose the likely routes of exposure in Section 11, “Toxicological Information”.
- 12. Correct the precautionary statements to select the appropriate phrases when a slash is present.
RN: 9962
Date of compliance undertaking: 2019-07-12
The claimant had been advised to correct administrative non-compliances in the SDS (or label) and had been further advised to amend the SDS (or label) as indicated below.
- 1. Disclose the Canadian initial supplier identifier.
- 2. Disclose the appropriate first aid measures.
- 3. Correct the disclosure of misleading information regarding the most important symptoms and effects, whether acute or delayed.
- 4. Disclose the product’s pH.
- 5. Disclose the product’s boiling range.
- 6. Disclose a sufficient description of the delayed and immediate effects, and chronic effects from short-term and long-term exposure.
RN: 10033
Date of compliance undertaking: 2019-07-19
The claimant had been advised to correct administrative non-compliances in the SDS (or label) and had been further advised to amend the SDS (or label) as indicated below.
- 1. Disclose the additional hazard classifications of “Skin Sensitizer — Category 1A”, “Carcinogenicity — Category 1” and “Serious Eye Damage — Category 1” and remove the hazard classification of “Eye Irritation — Category 2A”.
- 2. Disclose the information elements concerning the additional hazard and precautionary statements.
- 3. Disclose the symbols and/or the name of symbols for “Health Hazard” and “Corrosion” on the SDS.
- 4. Disclose the signal word “Danger”.
- 5. Correct the disclosure of misleading information regarding first aid measures.
- 6. Correct the disclosure of misleading information regarding personal protective equipment in section 6, “Accidental release measures”.
- 7. Correct the disclosure of misleading information regarding precautions for safe handling.
- 8. Correct the disclosure of misleading information regarding appropriate engineering controls.
- 9. Disclose the ACGIH TLV–TWA of 0.1 ppm and ACGIH–STEL of 0.3 ppm exposure limits for the ingredient “formaldehyde”.
- 10. Disclose an adequate product odour.
- 11. Disclose the product’s boiling range.
- 12. Disclose a sufficient description of the delayed and immediate effects, and chronic effects from short-term and long-term exposure.
- 13. Disclose the calculated product oral ATE value of 18 750 mg/kg (40% unknown).
- 14. Clarify if the ingredient “phosphorous acid” is part of the product composition and disclose all relevant information about this ingredient in section 3 of the SDS.
- 15. Clarify if the ingredient “phosphorous acid” is part of the product composition and correct the disclosure of misleading information regarding the LD50 (rat, oral) value for the confidential ingredient “phosphonic acid”.
- 16. Disclose the likely routes of exposure in section 11, “Toxicological Information”.
- 17. Disclose the symptoms related to the physical, chemical and toxicological characteristics.
- 18. Remove the reference to HMIRC on the SDS.
RN: 10035
Date of compliance undertaking: 2019-08-22
The claimant had been advised to correct administrative non-compliances in the SDS (or label) and had been further advised to amend the SDS (or label) as indicated below.
- 1. Disclose the additional information elements in the applicable SDS sections.
- 2. Disclose the Canadian initial supplier identifier.
- 3. Disclose the likely routes of exposure in section 11, “Toxicological Information”.
- 4. Disclose the symptoms related to the physical, chemical and toxicological characteristics.
RN: 10858
Date of compliance undertaking: 2019-07-25
The claimant had been advised to correct administrative non-compliances in the SDS (or label) and had been further advised to amend the SDS (or label) as indicated below.
- 1. Disclose the additional hazard classifications of “Skin Corrosion — Category 1”, “Acute Toxicity (Inhalation) — Category 3” and “Acute Toxicity (Oral) — Category 4” and remove the hazard classification of “Skin Corrosion — Category 1B”.
- 2. Disclose the symbol and/or name of the symbol for “Skull and Crossbones” on the SDS.
- 3. Disclose the percent of unknown toxicity of “9.3%” and “55%” for the calculated product oral and inhalation ATE values, respectively.
- 4. Disclose the information elements concerning the additional hazard and precautionary statements.
- 5. Disclose the applicable information for “the most important symptoms and effects, whether acute or delayed” under section 4, “First aid measures”.
- 6. Disclose statements conveying the relevant precautionary information in section 4 of the SDS.
- 7. Disclose information on the precautions for firefighters.
- 8. Disclose statements conveying the relevant precautionary information in section 7 of the SDS.
- 9. Disclose the product’s boiling range.
- 10. Disclose the product’s reactivity.
- 11. Disclose “aluminum, hydrogen peroxide (oxidizer), 4-hydroxy-3-methoxybenzaldehyde, thallium 3 nitrate, nitric acid (acids), urea, nitromethane, palladium, phosphorous pentoxide, and sodium hypochlorite (oxidizer)” as incompatible materials.
- 12. Disclose a sufficient description of the delayed and immediate effects, and chronic effects from short-term and long-term exposure.
- 13. Disclose the calculated product oral ATE value of 1 692 mg/kg (9.3% unknown) and calculated inhalation (vapour) ATE value 9.8 mg/L (55% unknown).
- 14. Disclose the likely routes of exposure in section 11, “Toxicological Information”.
- 15. Correct the precautionary statements to select the appropriate phrases when a slash is present.
RN: 11130
Date of compliance undertaking: 2019-07-12
The claimant had been advised to correct administrative non-compliances in the SDS (or label) and had been further advised to amend the SDS (or label) as indicated below.
- 1. Remove CANUTEC’s emergency telephone number.
- 2. Disclose the Canadian initial supplier identifier.
- 3. Disclose the additional hazard classification of “Specific Target Organ Toxicity — Repeated Exposure — Category 1”.
- 4. Disclose the information elements concerning the additional hazard and precautionary statements.
- 5. Disclose “Other hazards” on the SDS.
- 6. Disclose the applicable common names and synonyms for the ingredient “xylene”.
- 7. Disclose the incompatibilities of the product.
- 8. Disclose the delayed and immediate effects, as well as the chronic effects from short-term and long-term exposure.
- 9. Disclose the calculated product oral ATE value of 4 762 mg/kg (0% unknown) and calculated inhalation ATE value 29 mg/L (31% unknown).
- 10. Correct the disclosure of misleading information regarding the LD50 (rat, oral) value and LC50 (rat, inhalation [vapour]) value for the ingredient “xylene”.
- 11. Correct the precautionary statements to select the appropriate phrases when a slash is present.
RN: 11266
Date of compliance undertaking: 2019-07-12
The claimant had been advised to correct administrative non-compliances in the SDS (or label) and had been further advised to amend the SDS (or label) as indicated below.
- 1. Disclose the Canadian initial supplier identifier.
- 2. Disclose the additional hazard classifications of “Reproductive Toxicity — Category 1” and “Specific Target Organ Toxicity — Repeated Exposure — Category 1 (central nervous system and hearing loss)”.
- 3. Disclose the signal word “Danger”.
- 4. Disclose the information elements concerning the additional hazard and precautionary statements.
- 5. Correct the precautionary statements to select the appropriate phrases when a slash is present.
- 6. Disclose the percent of unknown toxicity of “55%” for the calculated product inhalation ATE value.
- 7. Disclose the applicable common names and synonyms for the ingredients “xylene” and “isobutanol”.
- 8. Disclose the appropriate first aid measures.
- 9. Disclose the most important symptoms and effects, whether acute or delayed.
- 10. Correct the disclosure of misleading information regarding extinguishing media.
- 11. Disclose the appropriate precautions for safe handling.
- 12. Disclose the product’s melting point and freezing point.
- 13. Disclose the product’s boiling range.
- 14. Disclose a sufficient description of the delayed and immediate effects, and chronic effects from short-term and long-term exposure.
- 15. Disclose the calculated product oral ATE value of 4 764 mg/kg (50.5% unknown) and calculated inhalation (vapour) ATE of 38 mg/L (55% unknown).
- 16. Correct the disclosure of misleading information regarding the LD50 (rat, oral) and LC50 (rat, inhalation) values for the ingredient “xylene”, and the LD50 (rat, oral) and LC50 (rat, inhalation) values for the ingredient “isobutanol”.
RN: 11267
Date of compliance undertaking: 2019-07-12
The claimant had been advised to correct administrative non-compliances in the SDS (or label) and had been further advised to amend the SDS (or label) as indicated below.
- 1. Disclose the Canadian initial supplier identifier.
- 2. Disclose the additional hazard classifications of “Reproductive Toxicity — Category 1” and “Specific Target Organ Toxicity — Repeated Exposure — Category 1 (central nervous system and hearing loss)”.
- 3. Disclose the signal word “Danger”.
- 4. Disclose the information elements concerning the additional hazard and precautionary statements.
- 5. Correct the precautionary statements to select the appropriate phrases when a slash is present.
- 6. Disclose the percent of unknown toxicity of “55%” for the calculated product inhalation ATE value.
- 7. Disclose the applicable common names and synonyms for the ingredients “xylene” and “isobutanol”.
- 8. Disclose the appropriate first aid measures.
- 9. Disclose the most important symptoms and effects, whether acute or delayed.
- 10. Correct the disclosure of misleading information regarding extinguishing media.
- 11. Disclose the appropriate precautions for safe handling.
- 12. Disclose the product’s melting point and freezing point.
- 13. Disclose a sufficient description of the delayed and immediate effects, and chronic effects from short-term and long-term exposure.
- 14. Disclose the calculated product oral ATE value of 4 764 mg/kg (50.5% unknown) and calculated inhalation (vapour) ATE of 38 mg/L (55% unknown).
- 15. Correct the disclosure of misleading information regarding the LD50 (rat, oral) and LC50 (rat, inhalation) values for the ingredient “xylene”, and the LD50 (rat, oral) and LC50 (rat, inhalation) values for the ingredient “isobutanol”.
RN: 11795
Date of compliance undertaking: 2019-07-26
The claimant had been advised to correct administrative non-compliances in the SDS (or label) and had been further advised to amend the SDS (or label) as indicated below.
- 1. Correct the precautionary statements to select the appropriate phrases when a slash is present.
- 2. Disclose the additional hazard classification of “Acute Toxicity (Oral) — Category 4”.
- 3. Disclose the information elements concerning the additional hazard and precautionary statements.
- 4. Disclose the applicable common names and synonyms for the ingredient “hydroquinone”.
- 5. Correct the disclosure of misleading information regarding personal protective equipment in case of accidental release.
- 6. Disclose the appropriate precautions for safe handling.
- 7. Correct the disclosure of misleading information regarding personal protective equipment for precautions for safe handling.
- 8. Disclose the appropriate engineering controls.
- 9. Disclose an adequate product odour.
- 10. Disclose the calculated product oral ATE value of 1 750 mg/kg (0% unknown).
RN: 12148
Date of compliance undertaking: 2019-08-19
The claimant had been advised to correct administrative non-compliances in the SDS (or label) and had been further advised to amend the SDS (or label) as indicated below.
- 1. Correct the precautionary statements to select the appropriate phrases when a slash is present.
- 2. Remove CANUTEC’s emergency telephone number.
- 3. Disclose the additional hazard classifications of “Skin Corrosion — Category 1” and “Serious Eye Damage — Category 1”.
- 4. Disclose the information elements concerning the additional hazard and precautionary statements.
- 5. Disclose the symbol and/or name of the symbol for “Corrosion” on the SDS.
- 6. Disclose the signal word “Danger”.
- 7. Disclose the applicable common names and synonyms for the ingredient “benzotriazol”.
- 8. Disclose the applicable information for “the most important symptoms and effects, whether acute or delayed” under Section 4, “First aid measures”.
- 9. Disclose emergency procedures to follow in case of accidental release.
- 10. Correct the disclosure of misleading information regarding personal protective equipment in section 6, “Accidental release measures”.
- 11. Disclose the applicable information in Section 7, “Handling and storage”.
- 12. Disclose an adequate product odour.
- 13. Disclose the product’s reactivity.
- 14. Disclose a sufficient description of the delayed and immediate effects, and chronic effects from short-term and long-term exposure.
- 15. Disclose the calculated product oral ATE value of 6 500 mg/kg (45.4% unknown) and calculated dermal ATE value of 6 500 mg/kg (45.4% unknown).
- 16. Disclose the likely routes of exposure in Section 11, “Toxicological Information”.
CLAIMS FOR WHICH THE SCREENING OFFICER ORDERED THE CLAIMANT TO COMPLY WITH THE APPLICABLE DISCLOSURE REQUIREMENTS
In the case of the following claims, either the claimant did not supply the screening officer with a signed undertaking or the screening officer was not satisfied that the claimant had taken the measures set out in the undertaking in the manner and within the period specified in it. Pursuant to subsection 17(1) of the Hazardous Materials Information Review Act, the screening officer ordered the claimant to comply with the requirements of the relevant legislation within 30 days from the expiry of the appeal period, except that the information in respect of which the claim for exemption was made does not have to be disclosed, and to provide a copy of the amended SDS to the screening officer within 30 days of expiry of the appeal period.
Pursuant to paragraph 18(1)(a) of the Hazardous Materials Information Review Act, the Chief Screening Officer hereby gives notice of information that the screening officer ordered to be disclosed on the SDS reviewed by the screening officer and the date of the order.
RN: 9710
Date of order: 2019-07-18
The claimant had been advised to correct administrative non-compliances in the SDS (or label) and had been further advised to amend the SDS (or label) as indicated below.
- 1. Correct the precautionary statements to select the appropriate phrases when a slash is present.
- 2. Disclose the additional information elements in the applicable SDS sections.
- 3. Disclose the additional hazard classifications of “Specific Target Organ Toxicity — Repeated Exposure — Category 1” and “Flammable Liquids — Category 1”.
- 4. Disclose the information elements concerning the additional hazard and precautionary statements.
- 5. Disclose the applicable common names and synonyms for the ingredients “xylene”, “methanol” and “heavy aromatic petroleum naphtha”.
- 6. Disclose the product’s relative density.
- 7. Disclose the calculated product oral ATE value of 6 460 mg/kg, dermal ATE value of 12 000 mg/kg and inhalation (vapour) ATE value of 42 mg/L.
- 8. Correct the disclosure of misleading information regarding the LD50 (rat, oral) and LD50 (rabbit, dermal) value for the ingredients “xylene” and “heavy aromatic petroleum naphtha”, respectfully.
RN: 9727
Date of order: 2019-07-18
The claimant had been advised to correct administrative non-compliances in the SDS (or label) and had been further advised to amend the SDS (or label) as indicated below.
- 1. Correct the precautionary statements to select the appropriate phrases when a slash is present.
- 2. Disclose the Canadian initial supplier identifier.
- 3. Disclose the additional hazard classification of “Acute Toxicity (Inhalation) — Category 3”.
- 4. Correct the disclosure of misleading information regarding product hazard classification.
- 5. Disclose the symbol and/or name of symbol for “Skull and Crossbones” on the SDS.
- 6. Disclose the percent of unknown toxicity of “77%” for the calculated product inhalation ATE value.
- 7. Disclose the information elements concerning the additional hazard and precautionary statements.
- 8. Disclose the applicable common names and synonyms for the ingredients “light aromatic solvent”, “heavy aromatic petroleum naphtha”, “ethylene glycol monobutyl ether” and “isopropanol”.
- 9. Disclose the calculated product oral ATE value of 4 100 mg/kg (0% unknown), dermal ATE value of 2 700 mg/kg (0% unknown), and inhalation (vapour) ATE of 4.6 mg/L (77% unknown).
- 10. Correct the disclosure of misleading information regarding the LD50/LC50 values.
- 11. Disclose that ingredient “ethylene glycol monobutyl ether” has been shown to cause damage to organs via a single exposure.
RN: 12100
Date of order: 2019-07-25
The claimant had been advised to correct administrative non-compliances in the SDS (or label) and had been further advised to amend the SDS (or label) as indicated below.
- 1. Correct the precautionary statements to select the appropriate phrases when a slash is present.
- 2. Disclose the additional information elements in the applicable SDS sections.
- 3. Disclose the telephone number of the Canadian initial supplier identifier.
- 4. Disclose the information elements concerning the additional hazard and precautionary statements.
- 5. Disclose the additional information elements in the applicable SDS sections.
- 6. Correct the disclosure of misleading information regarding the most important symptoms and effects, whether acute or delayed.
- 7. Disclose information on the precautions for firefighters.
- 8. Correct the disclosure of misleading information regarding personal protective equipment in section 6, “Accidental release measures”.
- 9. Disclose an adequate product odour.
- 10. Disclose the product’s boiling range.
- 11. Disclose “ingestion” as an additional likely route of exposure.
- 12. Disclose the symptoms related to the physical, chemical and toxicological characteristics.
- 13. Disclose a sufficient description of the delayed and immediate effects, and chronic effects from short-term and long-term exposure.
- 14. Disclose the calculated product oral ATE value of 26 000 mg/kg (0% unknown).
- 15. Correct the disclosure of misleading information regarding serious eye damage/eye irritation.
CLAIMS FOR WHICH THE SCREENING OFFICER ISSUED THE DECISION THAT THE CLAIM FOR EXEMPTION WAS EITHER PARTIALLY VALID OR INVALID
In the case of the following claims, the screening officer issued the decision that the claim for exemption was partially valid.
Pursuant to section 18 of the Hazardous Materials Information Review Act, the Chief Screening Officer hereby gives notice of information that the screening officer ordered to be disclosed on an SDS or a label pursuant to subsection 16(1) and information that has been disclosed on the relevant SDS or label in compliance with an undertaking, and the dates on which the orders and notices referred to in subsection 16.1(3) of the Act were issued.
RN: 9471
Date of order: 2019-07-25
The claimant had been advised to correct administrative non-compliances in the SDS (or label) and had been further advised to amend the SDS (or label) as indicated below.
- 1. Remove the reference to HMIRC on the SDS.
- 2. Disclose the additional hazard classifications of “Serious Eye Damage — Category 1” and “Acute Toxicity (Inhalation) — Category 4 (dusts and mists)”.
- 3. Disclose the symbol and/or name of symbol for “Corrosion” on the SDS.
- 4. Disclose the information elements concerning the additional hazard and precautionary statements.
- 5. Disclose an acceptable TWA exposure guideline for the confidential ingredient “aliphatic hydrocarbon; acid (1)”.
- 6. Disclose the product’s odour threshold.
- 7. Disclose the boiling range, evaporation rate, flammability, upper and lower flammability or explosive limits, relative density, solubility, partition coefficient, and viscosity.
- 8. Disclose the calculated product oral ATE value of 4 600 mg/kg (0% unknown), dermal ATE value of 50 230 mg/kg (45% unknown), and inhalation (dusts and mists) ATE value of 4.4 mg/L (48% unknown.)
DEPARTMENT OF HEALTH
HAZARDOUS MATERIALS INFORMATION REVIEW ACT
Filing of claims for exemption
Pursuant to paragraph 12(1)(a) of the Hazardous Materials Information Review Act, the Chief Screening Officer hereby gives notice of the filing of the claims for exemption listed below.
In accordance with subsection 12(2) of the Hazardous Materials Information Review Act, affected parties, as defined, may make written representations to the screening officer with respect to the claim for exemption and the safety data sheet (SDS) or label to which it relates. Written representations must cite the appropriate registry number, state the reasons and evidence upon which the representations are based and be delivered within 30 days of the date of the publication of this notice in the Canada Gazette, Part I, to the screening officer at the following address: Workplace Hazardous Materials Bureau, 269 Laurier Avenue West, 8th Floor (4908-B), Ottawa, Ontario K1A 0K9.
Véronique Lalonde
Chief Screening Officer
On February 11, 2015, the Hazardous Products Act (HPA) was amended and the Controlled Products Regulations (CPR) and the Ingredient Disclosure List were repealed and replaced with the new Hazardous Products Regulations (HPR). The revised legislation (HPA/HPR) is referred to as WHMIS 2015.
The claims listed below seek an exemption from the disclosure of supplier confidential business information in respect of a hazardous product; such disclosure would otherwise be required under the provisions of the relevant legislation.
Claimant | Product Identifier | Subject of the Claim for Exemption | Registry Number |
---|---|---|---|
Shell Catalysts & Technologies | CENTERA GT ™ Catalyst DN-3622 | C.i. and C. of one ingredient C.i. of two ingredients C. of one ingredient |
03338074 |
Jacam Manufacturing, 2013, LLC | Cl BALLS Smart Balls® Corrosion Inhibitor | C.i. of one ingredient | 03338133 |
Jacam Manufacturing, 2013, LLC | SP 3 Stim-Solv | C.i. of two ingredients | 03338134 |
Jacam Manufacturing, 2013, LLC | SuperCorr® X Part B | C.i. of two ingredients | 03338135 |
Baker Hughes Canada Company | CRW9952 CORROSION INHIBITOR | C.i. of seven ingredients C. of three ingredients |
03338451 |
Baker Hughes Canada Company | RE34150CRW CORROSION INHIBITOR | C.i. of four ingredients C. of two ingredients |
03338482 |
SUEZ Water Technologies & Solutions Canada | E.C.O.FILM EF2604 | C.i. and C. of one ingredient | 03338717 |
Stahl USA | RelcaLink 10 | C.i. and C. of
one ingredient C. of two ingredients |
03338903 |
Globalquimica Partners LLC | RDV-01-CBP | C.i. and C. of
one ingredient C. of two ingredients |
03338905 |
PCT Global LLC | Enduroshield Professional | C.i. of one ingredient | 03338994 |
PCT Global LLC | Enduroshield Auto Glass Professional | C.i. of one ingredient | 03338995 |
Guardian Chemicals Inc. | CROSSOVER | C.i. and C. of four ingredients | 03338996 |
Globalquimica Partners LLC | RDV-01 L | C.i. and C. of one ingredient | 03339115 |
Allnex Canada Inc., c/o Goodmans, LLP | EBECRYL® 4510 radiation curing resins | C.i. and C. of one ingredient | 03339191 |
Nalco Canada ULC | NALSIZE One 63242 | C.i. of three ingredients | 03339196 |
Nalco Canada ULC | NALSIZE One 63240 | C.i. of three ingredients | 03339197 |
Nalco Canada ULC | NALSIZE One 63243 | C.i. of three ingredients | 03339328 |
Fluid Energy Group Ltd. | Enviro-Syn® HCR-7000-WL |
C.i. and C. of one ingredient | 03339358 |
SUEZ Water Technologies & Solutions Canada | E.C.O.Film EF2401 | C.i. and C. of one ingredient | 03339595 |
DuPont Electronics & Imaging | Cyrel® Cylosol Component A | C.i. of one ingredient | 03339693 |
DuPont Electronics & Imaging | Cyrel® Cylosol Component B | C.i. of one ingredient | 03339694 |
Rampf Group Inc. | RAKU-FST RI-5501 | C.i., C., and the toxicological study name of three ingredients C.i and C. of one ingredient and C.i of two ingredients | 03339699 |
Gourley’s Auto Parts Ltd. | TARiffic Scent-Free Waterless Degreaser | C.i. and C. of four ingredients | 03339960 |
Compass Minerals Manitoba Inc. | ROCKET SEEDS™ PMZ LIQUID 2-16-0 | C.i. and C. of one ingredient | 03339961 |
The Lubrizol Corporation | LUBRIZOL® 677A | C.i. of one ingredient | 03339970 |
The Lubrizol Corporation | ANGLAMOL® 9001N | C.i. of two ingredients | 03340086 |
Nouryon Surface Chemistry LLC | Redicote E-11E | C.i. of one ingredient | 03340303 |
NCS Multistage | FFI 2000 M | C.i. of one ingredient | 03340368 |
NCS Multistage | FFI 2100 M | C.i. of one ingredient | 03340370 |
NCS Multistage | FFI 2200 M | C.i. of one ingredient | 03340375 |
NCS Multistage | FFI 2300 M | C.i. of one ingredient | 03340378 |
NCS Multistage | FFI 2400 M | C.i. of one ingredient | 03340381 |
NCS Multistage | FFI 2700 M | C.i. of one ingredient | 03340382 |
NCS Multistage | FFI 3000 M | C.i. of one ingredient | 03340383 |
NCS Multistage | FFI 3200 M | C.i. of one ingredient | 03340385 |
NCS Multistage | FFI 3300 M | C.i. of one ingredient | 03340386 |
NCS Multistage | FFI 3400 M | C.i. of one ingredient | 03340387 |
NCS Multistage | FFI 3500 M | C.i. of one ingredient | 03340389 |
NCS Multistage | FFI 3600 M | C.i. of one ingredient | 03340391 |
NCS Multistage | FFI 3700 M | C.i. of one ingredient | 03340393 |
NCS Multistage | FFI 3800 M | C.i. of one ingredient | 03340394 |
NCS Multistage | FFI 3900 M | C.i. of one ingredient | 03340395 |
Nouryon Surface Chemistry LLC | Redicote C-320 | C.i. of three ingredients | 03340396 |
NCS Multistage | FFI 2500 M | C.i. of one ingredient | 03340397 |
NCS Multistage | FFI 2600 M | C.i. of one ingredient | 03340398 |
NCS Multistage | FFI 8300 M | C.i. of one ingredient | 03340399 |
NCS Multistage | FFI 2900 M | C.i. of one ingredient | 03340400 |
NCS Multistage | FFI 8100 M | C.i. of one ingredient | 03340401 |
NCS Multistage | FFI 7000 M | C.i. of one ingredient | 03340402 |
NCS Multistage | FFI 3100 M | C.i. of one ingredient | 03340403 |
NCS Multistage | FFI 6400 M | C.i. of one ingredient | 03340404 |
NCS Multistage | FFI 6300 M | C.i. of one ingredient | 03340405 |
NCS Multistage | FFI 4100 M | C.i. of one ingredient | 03340406 |
NCS Multistage | FFI 6200 M | C.i. of one ingredient | 03340407 |
NCS Multistage | FFI 5300 M | C.i. of one ingredient | 03340408 |
NCS Multistage | FFI 5200 M | C.i. of one ingredient | 03340409 |
NCS Multistage | FFI 4200 M | C.i. of one ingredient | 03340410 |
NCS Multistage | FFI 4300 M | C.i. of one ingredient | 03340411 |
NCS Multistage | FFI 8400 M | C.i. of one ingredient | 03340412 |
NCS Multistage | FFI 8500 M | C.i. of one ingredient | 03340413 |
NCS Multistage | FFI 4500 M | C.i. of one ingredient | 03340414 |
NCS Multistage | FFI 4600 M | C.i. of one ingredient | 03340415 |
NCS Multistage | FFI 4700 M | C.i. of one ingredient | 03340416 |
NCS Multistage | FFI 4800 M | C.i. of one ingredient | 03340417 |
NCS Multistage | FFI 4900 M | C.i. of one ingredient | 03340418 |
NCS Multistage | FFI 5000 M | C.i. of one ingredient | 03340419 |
NCS Multistage | FFI 5100 M | C.i. of one ingredient | 03340420 |
NCS Multistage | FFI 5400 M | C.i. of one ingredient | 03340421 |
NCS Multistage | FFI 5500 M | C.i. of one ingredient | 03340422 |
Note: C.i. = chemical identity and C. = concentration
DEPARTMENT OF INDUSTRY
OFFICE OF THE REGISTRAR GENERAL
Name and position | Order in Council |
---|---|
Kenny, Leonard | 2019-1322 |
Deputy Commissioner of Northwest Territories | |
Murphy, Brenda Louise | 2019-1325 |
Lieutenant Governor of the Province of New Brunswick | |
Roy, Guylaine | 2019-1329 |
Deputy Minister of Tourism, Official Languages and La Francophonie to be concurrently Deputy Minister of Women and Gender Equality | |
Williams, Rebekah Uqi | 2019-1321 |
Deputy Commissioner of Nunavut |
September 19, 2019
Diane Bélanger
Official Documents Registrar
DEPARTMENT OF TRANSPORT
CANADA MARINE ACT
Montreal Port Authority — Supplementary letters patent
WHEREAS letters patent were issued by the Minister of Transport (“Minister”) for the Montreal Port Authority (“Authority”), under the authority of the Canada Marine Act (“Act”), effective March 1, 1999;
WHEREAS section 9.2 of the letters patent sets out a limit on the power of the Authority to borrow money on its credit for port purposes;
WHEREAS the board of directors of the Authority has requested that the Minister issue supplementary letters patent to increase the aggregate limit on the power of the Authority to borrow money on the credit of the Authority for port purposes set out in section 9.2 of the letters patent;
WHEREAS, by Order in Council P.C. 2019-1326 of September 6, 2019, the Governor in Council, pursuant to subsection 8(5) of the Act, approved the provisions of the proposed supplementary letters patent for the purposes of increasing the aggregate limit on the power of the Authority to borrow money on the credit of the Authority for port purposes;
AND WHEREAS the Minister is satisfied that the amendment to the letters patent is consistent with the Act;
NOW THEREFORE, under the authority of subsection 9(1) of the Act, the letters patent are amended as follows:
- 1. Section 9.2 of the letters patent issued to the Montreal Port Authority is replaced by the following:
- 9.2 Limit on Borrowing Power. The Authority shall not incur any item of Borrowing so that the aggregate Borrowing of the Authority would exceed $420,000,000.
- 2. These supplementary letters patent take effect on January 1, 2020.
ISSUED this 11th day of September, 2019.
The Honourable Marc Garneau, P.C., M.P.
Minister of Transport
DEPARTMENT OF TRANSPORT
CANADA MARINE ACT
Montreal Port Authority — Supplementary letters patent
WHEREAS letters patent were issued by the Minister of Transport (“Minister”) for the Montreal Port Authority (“Authority”), under the authority of the Canada Marine Act (“Act”), effective March 1, 1999;
WHEREAS section 9.2 of the letters patent sets out a limit on the power of the Authority to borrow money on its credit for port purposes (“borrowing limit”);
WHEREAS the board of directors of the Authority has requested that the Minister issue supplementary letters patent to add two additional borrowing limits specific to identified projects thereby increasing the power of the Authority to borrow money on the credit of the Authority for port purposes set out in section 9.2 of the letters patent;
WHEREAS, by Order in Council P.C. 2019-1326 of September 6, 2019, the Governor in Council, pursuant to subsection 8(5) of the Act, approved the provisions of the proposed supplementary letters patent for the purposes of adding two additional borrowing limits specific to identified projects;
AND WHEREAS the Minister is satisfied that the amendment to the letters patent is consistent with the Act;
NOW THEREFORE, under the authority of subsection 9(1) of the Act, the letters patent are amended as follows:
- 1. The letters patent are amended by adding the following after section 9.2:
- 9.2.1 Additional Borrowing Limit for the rehabilitation of the Iberville Cruise Terminal and the Alexandra Pier. Notwithstanding section 9.2, the Authority may, in addition to the aggregate amount referred to in section 9.2, and the additional borrowing provided for in section 9.2.2, borrow up to a maximum of $20,000,000 on its credit, specifically for costs associated with the rehabilitation of the Iberville Cruise Terminal and the Alexandra Pier, provided such borrowing be fully reimbursable in capital and interest by the Province of Quebec pursuant to the agreement between Tourism Quebec and the Authority dated June 17, 2016, and amended August 6, 2018.
- 9.2.2 Additional Borrowing Limit for development and consolidation of port assets. Notwithstanding section 9.2, the Authority may, in addition to the aggregate amount referred to in section 9.2 and the additional borrowing provided for in section 9.2.1, borrow up to a maximum of $40,000,000 on its credit, specifically for costs associated with the development and consolidation of port assets, provided such borrowing be fully reimbursable in capital and interest by the Province of Quebec pursuant to the letters issued by the ministère des Transports, de la Mobilité durable et de l’Électrification des transports du Québec dated March 24, 2017, and August 1, 2017.
- 2. These supplementary letters patent take effect upon issuance.
ISSUED this 11th day of September, 2019.
The Honourable Marc Garneau, P.C., M.P.
Minister of Transport
DEPARTMENT OF TRANSPORT
CANADA MARINE ACT
Vancouver Fraser Port Authority — Supplementary letters patent
WHEREAS the Governor in Council issued a Certificate of Amalgamation containing letters patent to amalgamate the Vancouver Port Authority, the Fraser River Port Authority and the North Fraser Port Authority and to continue as one port authority named the Vancouver Fraser Port Authority (“Authority”), effective January 1, 2008;
WHEREAS Schedule C of the letters patent sets out the real property, other than federal real property, held or occupied by the Authority;
WHEREAS, pursuant to subsection 46(2.1) of the Canada Marine Act (“Act”), the Authority wishes to acquire the real properties bearing parcel identifiers (PID) 009-900-489 and 013-197-754;
WHEREAS the board of directors of the Authority has requested that the Minister of Transport issue supplementary letters patent to set out the real properties in Schedule C of the letters patent;
AND WHEREAS the Minister of Transport is satisfied that the amendments to the letters patent are consistent with the Act;
NOW THEREFORE, pursuant to subsection 9(1) of the Act, the letters patent are amended as follows:
PID NUMBER | DESCRIPTION |
---|---|
009-900-489 |
|
013-197-754 |
|
- 2. These supplementary letters patent take effect on the date of registration of the title, in the New Westminster Land Title Office, of each parcel of land subject to these transactions.
ISSUED this 29th day of August, 2019.
The Honourable Marc Garneau, P.C., M.P.
Minister of Transport
OFFICE OF THE SUPERINTENDENT OF FINANCIAL INSTITUTIONS
ASSESSMENT OF PENSION PLANS REGULATIONS
Basic rate
Notice is hereby given, in accordance with section 5 of the Assessment of Pension Plans Regulations, that the Superintendent of Financial Institutions sets the basic rate, established pursuant to section 4 of the said Regulations, at $10.00 for the Office year beginning on April 1, 2020. In accordance with subsection 1(1) of the said Regulations, this rate applies to all pension plans registered under the Pension Benefits Standards Act, 1985 and the Pooled Registered Pension Plans Act.
September 16, 2019
Judy Cameron
Acting Assistant Superintendent
BANK OF CANADA
Statement of financial position as at August 31, 2019
ASSETS | Amount | Total |
---|---|---|
Cash and foreign deposits | 22.0 | |
Loans and receivables | ||
Securities purchased under resale agreements | 10,908.9 | |
Advances | — | |
Other receivables | 3.8 | |
10,912.7 | ||
Investments | ||
Treasury bills of Canada | 27,570.3 | |
Canada Mortgage Bonds | 513.7 | |
Government of Canada bonds | 79,849.3 | |
Other investments | 439.9 | |
108,373.2 | ||
Capital assets | ||
Property and equipment | 597.8 | |
Intangible assets | 50.9 | |
Right-of-use leased assets | 52.4 | |
701.1 | ||
Other assets | 44.0 | |
Total assets | 120,053.0 |
LIABILITIES AND EQUITY | Amount | Total |
---|---|---|
Bank notes in circulation | 90,801.4 | |
Deposits | ||
Government of Canada | 25,139.6 | |
Members of Payments Canada | 250.0 | |
Other deposits | 2,583.2 | |
27,972.8 | ||
Securities sold under repurchase agreements | — | |
Other liabilities | 747.0 | |
119,521.2 | ||
Equity | ||
Share capital | 5.0 | |
Statutory and special reserves | 125.0 | |
Investment revaluation reserve | 401.8 | |
531.8 | ||
Total Liabilities and Equity | 120,053.0 |
I declare that the foregoing statement is correct according to the books of the Bank.
Ottawa, September 18, 2019
Carmen Vierula
Chief Financial Officer and Chief Accountant
I declare that the foregoing statement is to the best of my knowledge and belief correct, and shows truly and clearly the financial position of the Bank, as required by section 29 of the Bank of Canada Act.
Ottawa, September 18, 2019
Stephen S. Poloz
Governor